Search results

Hi Martin, sorry, I wasn't trying to teach my granny how to suck eggs. As long as the oil level is somewhere around the full mark all will be fine I'm sure. Enjoy your 4. All the best Brian.

Hi Martin. Well, I've not heard that one before. Pull the dipstick out, wipe it off, replace it, pull it out again, and you should get a true reading. Over filling will not cause a leak from the sump, but it's not recommended.

After an epic drive all the way to Scotland, including driving on to John O' Groats, our intrepid trio drove to Cornwall. Pictured here in Falmouth, where friend Simon and I met up with them. A fantastic achievement Angelo, Massimo and Mario, true adventurers.

Hi Martin. I have KYB gas shockers on the back of my 85 GTL, I can thoroughly recommend them after 7 years of hard use, and I guess they do front one too. All the best Bry.

Welcome to the forum. There needs to be about 3mm of play of the cable at the fork end, 1/8th of an inch in old money, so the release bearing just clears the pressure plate.

Now I understand why you want originality, it makes sense I guess. Sorry I can't help with the problem you have, but you have come to the right place with members that have the knowledge, and I'm sure the problem will be resolved.

Is that such a problem Gabriele? We are lucky in the UK, but I didn't realise changing a small part like the dizzy would upset the system in your country.

Personally I would suggest you remove the distributor complete, along with the coil if its an old one, a bin them both. Next, invest in a good quality coil and a 123 electronic ignition distributor. Forget those crappy points and condensor and enjoy trouble free motoring. I know its not cheap...

This was my solution for fitting an oil pressure gauge. A pressure sensor fitted on the bulkhead, with a small bore plastic pipe down to the engine block. There is provision for the oil pressure light sensor as well. This was obtained from Car Builder Solutions, a British company based in Kent.

Yes I think torsion bars can go weak over time with hard use, so you could be right. Finding a NOS one might not be so easy, but worth a try, but failing that maybe just trying a second hand one might do the trick. Happy birthday, and enjoy your run out in the TC, a great little car. I've had...

Kevin, can I suggest you strip the other side, leaving the bottom wishbone and torsion bar in situ and undisturbed. Now you can try the offending bar in various settings until the two wishbones look to be in the same position/angle. Remember, you do have fine adjustment if you move each end of...

It's not easy to explain how to do this, but you do have to move both ends the same number of splines. Remember 22 at one end and 21 the other, so you have fine adjustment. I would fit the bottom arm back on, and when you think you have correct height use a small scissor jack to raise it up for...

Hello Martin. The dipstick on my GTL engine is 365mm long, and the tube is 185mm long. Hope this helps. Regards Bry.

I made up this adjustable bar to take the place of the rear shock absorber, and to give fine adjustment. With regard to the front torsion bar adjustment you need to count the splines. 22 at one end and 21 at the other, and turn the bar CW or ACW to get the desired height. With both operations of...

Once you disassemble the front suspension and leave the lower wishbone hanging, unbolt the rear anchor bracket. The torsion bar should simply pull free from the wishbone. With regard to the rear torsion bars, once the shock absorber has been removed, and the swinging arm supported with a jack...

Just a spray with WD40 or similar to clean the rod where it passes through the bush, and then a light spray with same to lubricate it. Hope this works Jonathan.

Camping near Beaulieu 2024.

Hope we get to meet up Leonardo.

Not sure what you are showing us there. Doesn't look very Renault 4 to me, or am I missing something? Try pressing the button by the gear-stick inside the car.

I guess it might be an idea Richard, just in case anyone else is thinking of joining us.